AccessZ Circle of Confusion Calculator v2.71

Precise personalization of CoC Diameters used in Depth of Field calculations (deploying the CoC equation found in the Wikipedia article titled, Circle of Confusion.)

Sensor & Final Image Specifications

This can be obtained from camera specs. (Ex: 54 w Phase One & Leaf MF, 45 w Leica-S MF, 44 w Hasselblad & Fujifilm MF, 36 w FF, 23.5 w most APS-C, 22.3 w Canon APS-C, 17.3 w M43.)
This can be obtained from camera specs. With film, assume it can resolve the equivalent of 4800 pixels per 25mm of exposed width, suffering no Bayer-induced resolution loss. (Ex: Enter 7200 for 35mm format film.)
Enter a value at or between 1 and 8 lp/mm (equiv. to final image densities of 50 through 400 ppi). Most people are not accustomed to viewing prints having subject detail at resolutions higher than 4 lp/mm (200 ppi), whether or not the printer's dpi is at a higher resolution. A 27-inch 4K monitor's resolution is ~3.22 lp/mm (~160 ppi). Healthy eyes cannot appreciate >8 lp/mm (400 ppi) at 25cm.
Note that smaller prints enable use of proportionally larger apertures (and thus, faster shutter speeds) for similarly percieved DoF.
How closely do you want the final image to survive scrutiny? (25cm or greater). If a more distant minimum viewing distance can be "defended," you can shoot with proportionally larger apertures, for similarly perceived DoF. (Some assume that all prints are viewed at distances equal to or greater than their diagonals.)

Calculated Results

Anticipated Maximum Enlargement Factor
—
This is the ratio of your Anticipated Maximum Final Image Width (in mm) and your Sensor Width (in mm).
Minimum Required Unresampled Final Image File Density (ppi)
—
Without resampling, the image file sent to the printer must have at least the Density calculated here, to achieve your Desired Final Image Resolution.
Bayer-Limited Enlargement Factor Ceiling for Desired Final Image Resolution
—
Film does not suffer the minimum 16.25% loss of resolution caused by a CMOS sensor's Bayer algorithm, but that will be accommodated here, if you have followed the suggestion that film can resolve the equivalent of 4800 pixels per 25mm of film width. (Example: Entering a value of 7200 pixels as the 35mm film format's Sensor Width, in pixels.)
Customized Maximum Permissible CoC Diameter (mm)
—
Specify this personalized maximum permissible CoC diameter in your choice of DoF apps or calculators that allow user-specification of CoC diameters, to support your Desired Final Image Resolution at the Near and Far limits of DoF. Note that precise measurements of the framed Near distance and later, of the DoF-calculated Focus distance, should be made using a tape measure (cumbersome) or a laser distance measure (quick and easy), such as the Bosch GLM165-40. Far distances can be estimated unless they are fairly close to the the Near distance. Precise focusing is also required, as can easily be done with Spot Back-Button Auto-Focus, if available. If you are content to estimate the Near and Focus distances, I suggest cutting this calculated CoC diameter in half, at least, when performing your DoF calculations, to then tolerate the proportionally longer exposures had with smaller DoF-calculated apertures, in order to still secure your Desired Final Image Resolution (while enjoying the arguably precious freedom that comes with haphazardly positioning the available DoF offered by the specified FL at the calculated aperture). I mean, why are you here? It's your choice how to shoot, ultimately. I'm just trying to equip you with the means to secure consistently satisfying results.
f-Number at which Diffraction will BEGIN to Inhibit Desired Final Image Resolution (f/N)
—
Shoot at this or smaller f-Numbers (larger apertures) to prevent diffraction's Airy disks from BEGINNING to inhibit your Desired Final Image Resolution, throughout the entire image.
AccessZ Inverse DoF Calculator